Replies – Forums – Keith Larsen

Forum Replies Created

Page 1 of 3

1 2 3 →

Keith Larsen
May 14, 2007 at 2:20 pm in reply to: upgrade in the morning

Don’t bother. FCS2 arrives tomorrow. Just hop up to FCP 6

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 11, 2007 at 3:29 pm in reply to: Alternatives to the “Basic Motion” tab in FCP

The strength of Digital Anarchy’s Re-Sizer in scaling up, but I’m sure its just as clean scaling down.

https://www.digitalanarchy.com/resizer/resizer_update.php

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 7:30 pm in reply to: same material digitized three different times and getting three different timecodes

I’ve seen this happen with “recycled” DV tapes. Is it a new tape?

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 7:28 pm in reply to: Converting quicktime files to .flv files

http://www.flip4mac.com

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 7:27 pm in reply to: Firewire deck conflict

Hopefully you didn’t fry the card in the deck. For the HD1200a it specifically warns you from pulling the firewire while the deck has power and I’ve had a few clients do exactly that and kill the card in the deck. Remember: FW carries POWER. If you have been spared frying the card in the deck, try resetting your mac hardware by re-booting and holding the COMMAN-OPT-P-R keys and letting the Mac startup chime ring about 3 times. Let go and it’ll boot. Hopefully that’s all that it’ll need. Try a different FW port as well.

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 5:47 pm in reply to: Installing FCP 5.1

Make sure you trash these found in the SYSTEM/LIBRARY/PREFERENCES as well as the User FCP prefs.
com.apple.RegFinalCutStudio.plist
com.apple.RegFinalCutPro.plist

This is the old registration information that it is accessing. Once you trash the prefs I would restart and hold the SHIFT key until the Mac boots into OS X “Safe Mode”. Run DISK UTILITY and repair permissions on the system drive. Empty any trash upon completion of repair using FINDER/SECURE EMPTY TRASH. Re-boot. All should be normal.

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 5:38 pm in reply to: Saving settings for still frame export using Quicktime conversion. ARRGH

Ditto for me. I always have to export still for websites and its such a pain the a** to go through the whole process each time to give them a smattering stills. Please Apple, allow to save settings in QTPro in version 8

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 5:35 pm in reply to: Sales pitch to Boss for Kona Card and AJA IO

A Kona LHor LHe (depending on your Mac) should satisfy your needs in most cases. You’ll be able to handle analog SD as well as SDI in both SD & HD. Check it out here:

https://www.aja.com/html/products_macintosh_kona_LHe.html

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
April 5, 2007 at 5:30 pm in reply to: To Render or Not to Render, That is the Question….

As long as your prefs are set to output to tape at full quality you can get away woth working in dynmaic or even medium to low res to push the capabilities of your hardware with FCP. Once you lay off to tape FCP will render anything that needs it into full res for layoff.

Keith Larsen
Founder
Connecticut Final Cut Pro User Group
CTFCPUG
Keith Larsen
December 19, 2006 at 5:27 pm in reply to: Playback issues

That’s THROW away your FCP prefs…ugh…in the middle of horrible project…

Page 1 of 3

1 2 3 →