Replies – Forums – Matt Dowling – Page 6

Forum Replies Created

Page 6 of 15

← 1 … 5 6 7 … 15 →

Matt Dowling
November 10, 2005 at 4:55 am in reply to: 5.2.2 some question

Hi Bill,

I am at a bit of a loss as to what is happening on your system. After reading your post, i set up a 1080/59.94 YUV project, imported an EDL with 200 clips, captured and then placed all 200 clips on the timeline at once at hit play – no problems. The clips varied in duration from 2 frames to 5 mins.

I placed them on the timeline at least 20 times on different video tracks each time as well – never had a serious error occur.

The systems this was tested with:

Dual core Opteron x2
Tyan, Thunder K8WE motherboard – on board SCSI RAID disabled in BIOS
3 ware 8 port SATA RAID card striped RAID 0 with 8 SATA 2 disks
nVidia Quadro FX 1300
2 GB ECC RAM
DeckLink HD PRO
HD D5 deck

Then we tested on the absolute bare minimum system we have (P4 32 bit PCI, single ATA disk) but in NTSC this time.
Same results.

Not being able to reproduce this error makes it very difficult for us to try and diagnose what is going on with your system.
I totally believe what you are saying – but we can not reproduce this on any of the systems here from the fastest to the slowest.

Regards,

Matt
Blackmagic Design
Matt Dowling
November 10, 2005 at 2:53 am in reply to: BlackMagic Codec to Video Ipod

Have you got the BMD XP codec installed?

Regards,

Matt
Blackmagic Design
Matt Dowling
November 9, 2005 at 10:48 am in reply to: Decklink Card and 9 pin deck control, What cable?

Hey Steve,

I just had to say – what an incredibly nice thing to do!

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 9, 2005 at 10:39 am in reply to: HDLink: simultaneous SD output?

Matthew,

HDLink is a HDSDI -> DVI-D/HDMI converter. This is not suitable for your intended workflow.

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 9, 2005 at 10:35 am in reply to: Help! Decklink HD Pro drops signal

Hi Sean,

Thanks – I will pass this onto the support guys to try and repo.

Just as a quick test, could you try the same thing with a 10 bit BMD project and let us know the results? If it’s what i think it might be this will help.

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 9, 2005 at 10:31 am in reply to: FrameLink and frame numbers

Hi John,

There are many option we want to get into FrameLink, TIFF is one of them. As Kaspar said, CS 1 & 2 open DPX.

We currently dont have any plans to sell FrameLink as a seperate app.

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 7, 2005 at 7:15 am in reply to: Video Blinking Issues with Burst In on Decklink HD Plus

Hi guys,

Below is a link to a build which i think will solve your problem.

https://www.blackmagic-design.com/downloads/software/seed/DeckLink_Macintosh_5.1.2e1.zip

Try this and please let me know how it goes.

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 7, 2005 at 4:32 am in reply to: Can BMD take on Avid’s DNxHDCodec?

Hey Jason,

Nice to hear from you – been a while man…

The main reason for the incompatibility between the two products is the fact Cineform
Matt Dowling
November 7, 2005 at 4:04 am in reply to: FrameLink and frame numbers

Hi Neil,

We have done exactly that on the PC version of FrameLink. We just haven’t rolled it into a MAC release as yet.

Cheers,

Regards,

Matt
Blackmagic Design
Matt Dowling
November 7, 2005 at 1:26 am in reply to: Video Blinking Issues with Burst In on Decklink HD Plus

HI Matt,

We are checking this out today for you – will get back to you ASAP.

Cheers,

Regards,

Matt
Blackmagic Design

Page 6 of 15

← 1 … 5 6 7 … 15 →