Vishesh Arora
Forum Replies Created
-
Joe
Just make a New Camera and particle will interact with it.
Can’t say much about the light part. Till now don’t think Comp Light will affect the particles. I might be wrong on this part.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Conrad
I think you are right. it might be possible.
The frame rate is included in the header of DPX file.
Film Information Header
The first industry header contains information used by the motion picture film industry. The information in this header describes the film and camera source from which the image frame data was derived. This header is 256 bytes in size and has the following format:typedef struct _IndustryFilmInfoHeader
{
char FilmMfgId[2]; /* Film manufacturer ID code */
char FilmType[2]; /* File type */
char Offset[2]; /* Offset in perfs */
char Prefix[6]; /* Prefix */
char Count[4]; /* Count */
char Format[32]; /* Format */
DWORD FramePosition; /* Frame position in sequence */
DWORD SequenceLen; /* Sequence length in frames */
DWORD HeldCount; /* Held count */
SINGLE FrameRate; /* Frame rate of original in frames/sec */
SINGLE ShutterAngle; /* Shutter angle of camera in degrees */
char FrameId[32]; /* Frame identification */
char SlateInfo[100]; /* Slate information */
BYTE Reserved[56]; /* Reserved field used for padding */
} INDUSTRYFILMINFOHEADER;Source : https://www.fileformat.info/format/dpx/egff.htm
Though there is a method to change it.
have a look at this thread : https://forums.creativecow.net/thread/223/13198
Use this link:
https://pomfort.com/dpxheadereditor/
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Eric
Interpret just one Sequence with 24 fps. Now select the footage in Project Panel, Right Click and Select Remember Interpretation .
Now select all the sequences, right click and select Apply Interpretation.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Glad to help
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Eric
I have searched almost everywhere and come to the conclusion that it’s not possible. Though you may cross check it by posting this at Adobe Forum.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
joey
Can’t say much about the Expression but I have a trick to work around using Numbers Effect.
See the example:
Increase_value_100.zipIf this isn’t suitable, You would get an appropriate answer at Adobe After Effects Expressions Forum.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Glad to help joey
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Kavon
Upload your file here :
https://www.dropbox.com/home/Ae_Files
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.com2011 3D Demo Reel:
https://www.youtube.com/watch?v=lHPgIJU_BR8 -
Eric
It’s very easy to make a starfield in After Effects using Red Giant’s Trapcode Particular Plugin . If you are not interested in buying the plugin the go for CC Particle World (Effects>Simulation>CC Particle World) whichcomes with AE.
In Particular there is already a preset for Starfield which after tweaking a little bit will give you the desired result.
For CC Particle World, go through these links:
https://cycorefx.com/dloads_ccfx.php
https://forums.creativecow.net/thread/2/961335
Kevin Camp has explained how to use Custom Particles.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.comDemo Reel(3D):
https://www.youtube.com/watch?v=lHPgIJU_BR8Email : vishesharora82@gmail.com
-
Dan
I believe that Rotobrush is not working for the whole clip. See the Image below:
Drag the area that I have highlighted in red box till where you want Rotobrush to do it work.
It may solve the problem.
Vishesh Arora
3D and Motion Graphics Artist
Films RajendraBlog:
https://digieffects.wordpress.comDemo Reel(3D):
https://www.youtube.com/watch?v=lHPgIJU_BR8
