Replies – Forums – Gautam Pandey – Page 3

Forum Replies Created

Page 3 of 6

← 1 2 3 4 … 6 →

Gautam Pandey
April 28, 2011 at 7:36 pm in reply to: Rendering confusion

Super! Thanks a ton John.. will do this first thing tomorrow 🙂

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
April 28, 2011 at 2:55 pm in reply to: Rendering confusion

Hi John,

Thank you for responding!

I think you’ve got it.. basically i have 3 way CC on most of my clips, this is now rendered.

I now need to burn TC on the entire sequence.

Correct me if i’m wrong.

So if i now nest my sequence and then lay another layer over it for the TC, the sequence would need to be re rendered only the layer with TC will.

Thanks

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 19, 2011 at 6:18 pm in reply to: 5D Mark II 24p Audio Sync?

Thanks Brent,

Is there any loss through the 1/4″ cable? ( not sure about the cable specs 🙂 )

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 11, 2011 at 7:02 am in reply to: Unable to install AJA Control Panel

This is the response i got.. and it worked! 🙂

Please make sure you’re using the correct IO driver version and control panel compatible with your Mac OS version. The drivers point out the requirements. Please read the notes.

Try the following steps to see if it helps.

1. Reset the IOLD to factory. You will need a paper clip to press the reset button.

Located on the back and left of the multi pin audio connector you will see the reset. Insert the paper clip while the IO is turned on and press down and hold the reset while you turn off the IO then back on and release the reset.
2. Make sure the IO is the only firewire device connected to the Mac.

Shut down the IO and the Mac wait about 10 seconds and boot up the IO first then the Mac.
3. Download the IO firmware update version 21-26 form the AJA website https://www.aja.com/support/io/io-archive.php

run the updater and follow the prompt instruction. Once done you will need to reboot the IO and Mac as explained above.
4. Open the IO control panel and click on the Preset tab to update the IO once again by clicking on the Update Firmware message.

Follow the prompt instruction and reboot the IO and Mac once again when done.

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 10, 2011 at 4:09 am in reply to: Unable to install AJA Control Panel

Sorry.. not an editor so still might not have complete info to offer 🙂

Specs

Mac OS 10.4

FCP 6.0

AJA IO captures only SD

The software is the latest version downloaded from the AJA site

Thanks

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 10, 2011 at 4:09 am in reply to: Unable to install AJA Control Panel

Thanks! i’ll do that

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 9, 2011 at 5:07 am in reply to: Log & Capture Mystery!

Followed the instructions..

I downloaded it.. installed it.. and doubled clicked the icon to launch.

The software crashes and fails to open.

I turned the IO box off, application launches.. but ofcourse says could not detect hardware.

With the app launched if i turn the IO box on.. the app crashes

Any ideas on this?

Thanks

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 8, 2011 at 3:25 am in reply to: 5D Mark II 24p Audio Sync?

Thanks Danny… Great video by the way 🙂

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 5, 2011 at 12:24 pm in reply to: Portable Field Recorders and why 4 track?

Bing! and the cloud has lifted 🙂

Thanks Eric

Gautam Pandey
http://www.riverbankstudios.com
Gautam Pandey
March 5, 2011 at 12:23 pm in reply to: Portable Field Recorders and why 4 track?

Thanks Dave! lots of info! and thank you for the review cleared up a lot of things 🙂

Cheers!

Gautam Pandey
http://www.riverbankstudios.com

Page 3 of 6

← 1 2 3 4 … 6 →