Kurt Hennrich
Forum Replies Created
-
…. and you are shure that your deck is ok?
as it sounds, the EQ board of the deck might be damaged -
see my:
https://www.1z1.at/plugins/the DisplaySourceTC plugin also can display source name and its free
all the best,
kurt -
look for a software called
TransType
works perfect to convert fonts from/to
PS/TT/MAC/PC -
[rafalaos] ” but the bright and the contrast”
hi rafalaos
my method:
when adjusting brightness : look at black
when adjusting contrast : look at whiteblack of PAL-bars is 0%, white is 100%. therefor:
switch monitor to underscan and raise brightness until it differs a bit from the ‘no image’ area. now lower brighness a bit so that compared to ‘no image’ black is barely visible.
reduce contrast until bar-white dimmes. now raise contrast a bit so that white is pure white again.
once again for brightness, once again for contrast.looking at the colorbars adjust saturation by pushing ‘blue only’ at the monitor and adjust sat until the blue bars are equal bright.
…. this all only makes real sense with a good monitor (without ‘auto gain’ behaviour)
kurt
-
[rafalaos] “I’m in PAL-land and my monitor got “blue-only” so happy about that. but I have to calibrate it with NTSC bars, because I haven’t found no where how to do it properly with the PAL bars, silly, isn’t it?
“calibration of saturation with PAL-colorbars is quite as easy:
press ‘blue only’ and adjust chroma value until all bright(blue) bars are equal bright. -
to bring 8channels from MB AES out to analog for monitoring is expensiv.
if MB would have an ADAT interface, an optical cable + one of the multiple ADAT2analog interfaces from the audio/music world would be a much simpler and cheaper solution with lots of other options I thought.
kurt
-
[Jean-Philippe Mariani] “Decklink drivers simply can’t do it by now….”
thank you Jean-Philippe.
to kristian & all the others at BM:
please make it happen as soon as possible. we really need the HDV 25p/50p functionality here in europe. now. jvc has landed :/thank you,
kurt -
[Kristian Lam] “Hardware down conversion only supports up to 2 channels (see technote in URL below and search for the text ‘audio’) but you’re correct about the channels being flipped. I’ve notified the engineers and they will be addressing this. Sorry”
thank you kristian.
good to hear that it’s not me who is flipped.thought, I have never heared about the 2 channel limitation
and this defenitely is a fact that should be mentioned in product brochures
and not just in technotes.btw.: is this 2ch issue also true for the multibridge series?
thank you,
kurt -
[Bob Zelin] “Stop being so curious, and get back to work. “
from my point of view
there is a lot of headroom for improvements within the current specs:– teranex quality up/downconversion during capture and playback (hd<>sd, letterboxed<>anamorph, etc..)
(maybe even in a ‘loop throug’ way to playback/convert/record on the same host in one pass)
– noice reduction during capture
– at least 8 channel audio output in all digital&analog formats with adjustable delay to compensate sync drifts of different monitoring paths (monitor vers. projector, dolby processor etc.)
– capture from firewire via high quality scaling to uncompressed sd/hd
– TC overlay, TC > audiotrack, audiotrack > TCthese are just some features that would make my work easier, faster, reduce some additional boxes from my setup (including mikeymouse power supplies)….. and maybe even reduce total costs of ownership.
and to LaCie:
give me a rackmountable FW800 hub/switch for at least 6 drives
and with one! power supply build in for all these drives.
-> no more in need to route FW800 signal through different disks (in different conditions) of different clients,
no more cables and power boxes on the table/floor, all of them produceing unnecessary heat.kurt
-
[Chris Poisson] “Kurt,
What is the 1z1 plugin?”
chris,
please see my site with detailed info about the plugins at:
https://www.1z1.at/plugins/all the best,
kurt