Forum Replies Created

Page 16 of 51
  • Scott Davis

    June 3, 2010 at 2:39 pm in reply to: FCP registration

    What if I install the OS and then FCS on the hard drive. Then boot up to that specific drive (the one with FCS 3 and the OS) on it? I can’t test it out for a few days; so I’m just trying to think through this.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 27, 2010 at 7:51 pm in reply to: Deal Memo payment clause

    Thanks David, Is net 10 normal for the industry?

    I found this in a pre witten deal memo on the internet. What do you think?

    22. PAYMENT: Production services fees shall be paid to Contractor within 14 days after Companyʼs receipt of Contractorʼs invoice. Pay date may be delayed by reason of an intervening federal or state holiday. Employee shall not receive any overtime, turnaround or other hourly payments. Paid work on a day off or a holiday must be approved in advance by Company and will be paid at the normal rate provided for by this Deal Memo.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 21, 2010 at 6:34 pm in reply to: Relinking Nightmare

    Media is tape based (HDV, Beta, DV, HDCAM) and QTs (basically everything you can think of), AIFF, JPEGS,PICTS, etc.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 21, 2010 at 6:32 pm in reply to: Relinking Nightmare

    Interesting. I will give that a shot and see how it goes.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 21, 2010 at 6:32 pm in reply to: Relinking Nightmare

    So if I had not of selected “delete unused media” then it would have copied over the entire clip and linked all instances of it to the one clip? If that is so, then I feel much better as it was operator error and not something inherently wrong with MM.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 21, 2010 at 4:59 pm in reply to: Relinking Nightmare

    I did not rename anything!!! Media Manager did that when there is multiple instances of the same piece of media it adds a number at the end of the clip.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 21, 2010 at 4:57 pm in reply to: Relinking Nightmare

    No its not. FCP is asking for the media managed clip name (ie IV_Blow, Joe_034 4) not for the original clip name (ie IV_Blow, Joe_034). If I have multiple instances of this then I have to manually locate clip and point it to this. This is a 4 hour doc with 250+ hours of footage and 1000s of pieces of archival. Secondly, all my media is not in one folder. I have a finder based organizational system. GFX in one folder, music in another, etc. Captured media goes in the FCP scratch disc folder.

    I wish Philip Hodgets Matchback Magic had been around when we started this.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    May 14, 2010 at 2:15 pm in reply to: OT-Changing the name of a Disc Image

    It has a date in the name and I want to reuse it with a current date.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    April 28, 2010 at 4:03 pm in reply to: New York editor rates

    Both actually, most I would say online. But some still want a physical copy.

    Scott Davis
    View Scott Davis's profile on LinkedIn

  • Scott Davis

    April 27, 2010 at 8:24 pm in reply to: New York editor rates

    Nicholas, I’m sure rates very by experience, credits, project; but the documentary films I have worked on averaged around $500/day for offline. I can’t say I’ve got much advice as I’ve only been here a year and a half. Things were really, really, really slow over the winter. In the last couple of months it seems like the ice is thawing and work is proceeding. At least in my immediate experience. Can’t speak for others though. Good luck and if you ever want to meet for a coffee and chat when you get here shoot me an email or if you have any other questions. A lot of people helped me when I got here so I like to pass that help along.

    Scott Davis
    View Scott Davis's profile on LinkedIn

Page 16 of 51

We use anonymous cookies to give you the best experience we can.
Our Privacy policy | GDPR Policy