Replies – Forums – James Orlowski – Page 2

Forum Replies Created

Page 2 of 16

← 1 2 3 … 16 →

James Orlowski
May 22, 2012 at 5:19 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Just got off the phone with Blackmagic tech support. They didn’t seem to be aware of this problem, but at least now they are after talking to me.

4×3 SD probably just isn’t a priority for them, but it seems a fix should be simple if they just “write in” a compensation “stretch” value for the outputs.

BTW, this problem doesn’t happen in After Effects, so that’s my work around should I need to output to BetaCam SP.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 14, 2012 at 2:22 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Also, this problem doesn’t occur in After Effects. Only Premiere.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 14, 2012 at 1:09 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

I had 9.5 drivers installed on this same system with CS5.5 for a short while before my CS6 came.

I had not seen this problem with 9.5 and CS5.5, so it must be some problem with 9.5’s drivers interacting with CS6 that’s causing the “squeezed” 4×3 output.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 7:20 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Don’t see a 9.5.1 in the support section, only 9.5. Where’d you get 9.5.1.?

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 7:19 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Didn’t know there was a 9.5.1 update. Must have just happened. I’ll try it.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 7:18 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Thanks for your confirmation of the problem. At least I’m not crazy.

I upgraded one of our 4 suites to CS6. Perhaps I’ll wait to upgrade the others.

I suppose SD 4×3 isn’t on their priority list.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 6:13 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

UPDATE 2:

This only seems to happen on 4×3 Blackmagic sequences. 16×9, regardless of the resolution, work fine (seemingly).

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 5:03 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

Update: it’s not just “squeezed” on the SD-SDI output monitor, but also on my analog monitor attached to my BetaCam SP deck.

https://vimeo.com/41994179

Direct video clip download: https://dl.dropbox.com/u/280996/BMsqueezed.mov

So, with this current set-up, I’m unable to dub anything to Beta. Which isn’t too often lately, but does come up for time to time.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
May 11, 2012 at 4:45 pm in reply to: PPro CS6 and Decklink Studio 2 with 9.5 drivers

BTW, here’s a (poor quality) snapshot of what I see on my Sony SD-SDI monitor when viewing a 486i 29.97fps job.

https://dl.dropbox.com/u/280996/BMsqueezed.jpg

Note the green garbage along the left and right of the screen, and the non-circular shape that is a true circle in the titler track.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966
James Orlowski
June 21, 2011 at 6:21 pm in reply to: DeckLink Studio, CS5.5, and 8.01 Drivers

I found the solution burred in the “Settings…” in the audio Hardware preference tab.

But for me, it’s no longer in that drop down box as it was before.

—
James Orlowski
RYNO Production, Inc.
http://www.rynoproduction.com
800-860-7966

Page 2 of 16

← 1 2 3 … 16 →