Forum Replies Created

Page 82 of 215
  • Daniel Low

    May 22, 2009 at 11:35 am in reply to: DVCpro HD encode for SD DVD

    Are you using frame controls to do the deinterlacing in compressor? What settings have you tried for resizing?

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 21, 2009 at 2:00 pm in reply to: Mpeg2

    I assume you have the Quicktime MPEG-2 component installed? Do you think it would play if you didn’t?
    What does the Apple DVD player do with it?
    Did VLC play it as 1280×720?
    Strictly speaking, Episode shouldn’t have allowed you to create a non-standard output, it’s great that it does, but it should warn you or something.

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 20, 2009 at 11:42 pm in reply to: Mpeg2

    Like I said, the resolution you want is not supported by the MPEG-2 spec. Why does your client want MPEG-2?

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 20, 2009 at 3:03 pm in reply to: Mpeg2

    MPEG-2 does not support that resolution. The closest you will get is 1280×720
    Why does the client want it in MPEG-2?

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 20, 2009 at 10:30 am in reply to: Frame by frame player

    Sadly this can’t open MP4 files and crashes with WMV files and I couldn’t find any frame by frame controls 🙁

    I expected better from BM!

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 19, 2009 at 9:41 pm in reply to: H.264 Compression with QuickTime

    I totally agree with Craig, Apple’s implementation of H.264 is near the bottom of the pile. I’ve recently competed a series of transcodes of high quality but complex sources using the x264 codec to 720p with an average datarate of 2.5Mbits/s, single pass. The quality is stunning.

    A typical Apple movie trailer at 720p is 5.1Mb/s

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 19, 2009 at 9:29 pm in reply to: Best quality compression for DVD

    It really helps if you could tell us your source format!

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 19, 2009 at 6:04 pm in reply to: DVD player won’t play

    Yes, a true 7.0 CBR plus audio plays on everything I’ve come across. Bear in mind that this is still a very high datarate and should only be needed for most demanding types of content.

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 19, 2009 at 11:51 am in reply to: Best quality compression for DVD

    What is your source format?

    Where is the DVD likely to be viewed? Is it for general distribution or is there a very good chance that your clients will be viewing it on flat panel displays?

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

  • Daniel Low

    May 18, 2009 at 9:24 pm in reply to: Ideas for Archiving 5,000 Minutes of ProRes Video

    [Brian Alexander] “I’ve notice that leaving the settings to “Automatic” and “Best Quality” that the bit rate usually ends up around 16 Mbps, double my standard target of 8 Mbps. I figured this might double because we’re going from a 4:2:0 to a 4:2:2 but I’ve found no documentation that supports this; only wishful thinking. “

    https://en.wikipedia.org/wiki/H.264#Software_encoder_feature_comparison

    [Brian Alexander] “Nope, I do not know much about tapes. Are they expensive? What does a Data Tape Deck cost? What format do I lay to Data tape or is it just Data in general? Would I still want to compress my video to save on tape costs? I’m set up for an all digital and optical workflow so I haven’t considered much else since I have so much material coming in. “

    There are a number of different tape formats to consider and yes the initial outlay can seem expensive but tape nearly always works out the cheapest per bit in the long run but there are many other factors to consider i.e. speed, accessibility and so on

    The main ones to look at are AIT, DAT and LTO. If you are happy with Blu-Ray then it’s likely that this will be the best on-going option for you as media is easy to come by will just get cheaper and you have already made the investment in hardware.

    __________________________________________________________________
    Two years from now, spam will be solved. – Bill Gates, World Economic Forum 2004

Page 82 of 215

We use anonymous cookies to give you the best experience we can.
Our Privacy policy | GDPR Policy