Replies – Forums – Andrea Stewart

Forum Replies Created

Page 1 of 11

1 2 … 11 →

Andrea Stewart
April 25, 2017 at 12:29 pm in reply to: MXF playback is not smooth – advice

Media is on an internal RAID. And previews are on the SSD.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
April 25, 2017 at 12:28 pm in reply to: MXF playback is not smooth – advice

Doesn’t matter if it’s full, half or quarter

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
May 15, 2014 at 3:16 pm in reply to: Flash Frames in a WMV

I did indeed have keyframes set to every 10 seconds. I will give your idea a try.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
May 15, 2014 at 3:08 pm in reply to: Flash Frames in a WMV

Sorry, yes they were self contained. Though I must admit I did not watch them on an NTSC monitor.

However, the flash frames were showing up on the computer monitor.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
February 6, 2012 at 3:44 pm in reply to: Audio Config for LHi with a Mixer

Okay… Anyone? Beulher? Anyone?

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
November 4, 2011 at 3:02 pm in reply to: Interlace showing up in sequence

Sorry, a little more info.

Its a broadcast reel with all sources arriving SD on digibeta from the network. So everything should be 29.97 source. All other clips on the sequence are playing fine.

I did a test sequence of just this one clip. Dropped it on and same result.

I’m beginning to think this is some artifact of the way in which it was shot. Maybe it was shot with a DSLR or in 24p or 25 and pull down was added.

Either way, I think I’m just stuck with it the way it is.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
August 26, 2011 at 10:28 pm in reply to: Audio in viewer cuts out

You’re a high roller there David.

I think I had version 3.0 drivers. Uninstalled and reinstalled version 3.1. (I had recently updated to snow leopard which could be the cause of a conflict.) Hopefully that will do the trick.

BTW, I was also getting General Error (49) occassionally when I would try to advance or go back by one frame using the arrow keys.

Maybe that will disappear too.

Thanks!

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
August 15, 2011 at 9:26 pm in reply to: Tutorial to create Bokeh Effect

Thanks Walter.

I’d like to have the look of the stock footage, but with more control. Mostly, I want to add an obscuration layer (specifically a photo) in 3D so the lights can pass over and around it.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
May 18, 2011 at 5:40 pm in reply to: Aliasing after capturing to 10 bit

SDI cable (via AJA) vs firewire did the trick. Don’t know why it didn’t do a good job via firewire the first time, but now I know.

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC
Andrea Stewart
May 13, 2011 at 3:07 pm in reply to: Aliasing after capturing to 10 bit

So let me get this further further straighter. I should re-ingest via SDI at 10bit?
Or I should re-ingest at DV50 and deal with clips in my sequence that need to be rendered?

Andrea Stewart
Producer/Editor/Director – Owner
Germane Creative LLC

Page 1 of 11

1 2 … 11 →