Replies – Forums – Steve Eisen – Page 56

Forum Replies Created

Page 56 of 366

← 1 … 55 56 57 … 366 →

Steve Eisen
May 21, 2012 at 10:46 pm in reply to: export for iMovie

[Bob Cole] “I don’t have iMovie, so I’m at a bit of a loss. “

You are at a loss. If you have a Mac, iMovie comes pre-installed fro FREE!

Steve Eisen
Eisen Video Productions
Vice President
Chicago Creative Pro Users Group
Steve Eisen
May 21, 2012 at 9:43 pm in reply to: Best Thunderbolt I/O card for under $500?

The ioXT will play nice with all three NLE’s.

Matrox MXO2 LE is a little bit less expensive alternative. They work with all 3 NLE’s but use a different driver for MC6. You will need to have a second boot drive or do the unisnstall/reinstall each time you switch apps.

$500 is a VERY LOW number for a Tbolt i/o device.. The soon to be released T-Tap is an alternative solution. It is output only. Under $300.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 21, 2012 at 9:27 pm in reply to: Use of Shot Put Pro on Mac Book Pro — how many processors to specify?

Shoot an email to Imagine Products.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 21, 2012 at 9:20 pm in reply to: Manfrotto 503 head

I would’nt say cheap construction. It’s a basic video head. The weight of the camera and other accessories on the camera contribute to the problem. Make sure the tripod is evenly leveled to the ground and the camera weight is distributed evenly on the head. Sometimes the 501 Long plate helps.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 21, 2012 at 8:19 pm in reply to: Manfrotto 503 head

Not much you can do with the 503 head. The 504HD and 502HD have the new Bridging Technology with a lot more control over the tilt, drag and counterbalance. Similar, but in no way close to a Sachtler. The 503HDV was a slight improvement over the 503.

You did not cause any damage to your head.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 19, 2012 at 10:21 pm in reply to: Adobe Premiere 6 clips to FCP 7

If any intelligent shooter/editor knows what they are doing, they should have backed up the complete file structure from the 5D. Request those files. Make sure they give you more than just the h.264s.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 18, 2012 at 8:56 pm in reply to: Adjusting pixel aspect ration HPX250?

[Dave Felder] “When I shoot AVC-I 50 at 720P, my HPX250 is giving me 960×720 at 1.33”

This is normal. There is no way to change it. When you edit, your NLE will correct for it.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 17, 2012 at 7:27 pm in reply to: Comparing Minidv in dvx100 and hvx 200

There is NO difference DV is DV. There is a world of difference shooting HD onto P2 cards with the HVX200.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 17, 2012 at 7:26 pm in reply to: Edit to Tape – timecode showing up but video is black/blank when played back? Any thoughts welcome

I’m not 100% sure that the 1500A does edit to tape. It may only be available on the higher end decks. Try print to tape or do a crash record.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group
Steve Eisen
May 17, 2012 at 2:50 pm in reply to: Edit to Tape – timecode showing up but video is black/blank when played back? Any thoughts welcome

Make sure you have the correct input set on the deck. I’ll assume you are using Component in. Make sure BM card is set to Downconvert.

Steve Eisen
Eisen Video Productions
Vice President
Chicago Final Cut Pro Users Group

Page 56 of 366

← 1 … 55 56 57 … 366 →