Replies – Forums – Nelson May – Page 15

Forum Replies Created

Page 15 of 21

← 1 … 14 15 16 … 21 →

Nelson May
November 22, 2007 at 4:29 am in reply to: help with rotating a logo (new guy question)

Thanks Jon,

I am on Proanimator (I need to make a signature) and I think I got it to work. Here is a link. Serge will sometimes take a look at files. Maybe you can diagnose this one. When the logo rotates I lose one of the “N’s” at about 270 degrees. It is far enough sway from the spires. I just can’t figure out why I am getting a glitch.

https://homepage.mac.com/nelsonmay/FileSharing7.html or https://homepage.mac.com/WebObjects/FileSharing.woa/wa/Nelson_at_Nite_Logo_1.m4v.m4v-zip.zip?a=downloadFile&user=nelsonmay&path=.Public/Nelson%20at%20Nite%20Logo%201.m4v
Nelson May
November 21, 2007 at 12:46 am in reply to: Export with compression to motion and FCP

Yes and thanks.

I don’t like to compress twice.
Nelson May
November 17, 2007 at 4:34 pm in reply to: Zax New Guy Question

thanks Serge,

I look forward to leaning the program this afternoon. Be prepared I am man of many questions.
Nelson May
November 17, 2007 at 6:11 am in reply to: Zax New Guy Question

thanks again,

Funny I have Illustrator CS2 installed. Must have been with the suite I bought. When I get zax up and running, I wil let you know how I am progressing.

thanks again for the .ai file.
Nelson May
November 17, 2007 at 5:21 am in reply to: Zax New Guy Question

Hi Serge,

thanks for the quick reply. I was just going to export basic shapes to start with then see what I can do later. I may have an earlier version of illustrator laying around. How far back can you go with Illustrator (the version) to export vector paths.

There is a logo on this page that someone made for me a few years ago. It is between the guy and below the TV 21 banner. http://www.nelsonatnite.com/

I would like to 3D the object and maybe extrude the large “N’s” and the small Nelson at Nite that is in bruch script.
Nelson May
November 16, 2007 at 4:56 am in reply to: Good cheap intuitive 3D software?

Thanks for the help. I have a PC but it is old and I am not sure how much I can do with it. If I go with Leopard then I can run Parallels, and XP in my MAC and go from there.

Again I appreciate the help. I just wished I had a machine that could run it properly.
Nelson May
November 11, 2007 at 5:11 am in reply to: Zaxwerks Light?

I don’t have AE, only motion. I don’t think this is a stand alone is it?
Nelson May
November 6, 2007 at 3:00 am in reply to: DUH! how do I start a new 4:3 ration in motion

Thanks. Also for the shortcut
Nelson May
September 21, 2007 at 7:37 pm in reply to: Help with a serious export issue

can I output the file at a lower rate for the initial .mov file then conver to .mp4 for yet a smaller file?
Nelson May
August 22, 2007 at 1:38 am in reply to: Brain malfunction: Does FCP 5.1 have DVCPRO 50 codec

pardon my brain freeze, but I don’t see it on the easy set up pull down menu…..can I just use DV NTSC or do I need to load the codec from my install disk?

Thanks,

Page 15 of 21

← 1 … 14 15 16 … 21 →