Replies – Forums – Mark Fanjoy – Page 7

Forum Replies Created

Page 7 of 12

← 1 … 6 7 8 … 12 →

Mark Fanjoy
June 12, 2010 at 2:21 pm in reply to: Wrong Configuration To Imrove Rendering Speed?

Wow! A lot of great input. Thank you everyone! Makes me feel more comfortable about my expensive purchase, if nothing else. I bought the RAID primarily for peace of mind to protect my client data. But was hopeful increased rendering speed would be a lucky bonus.

Thanks again everyone for your insights.

Fanjoy

Wherever I am…I’m lost!
Mark Fanjoy
June 11, 2010 at 12:45 pm in reply to: Edit Bay To Edit Bay Mobile Drive Recommendation

I’ll look it up. Thanks!

Fanjoy

Wherever I am…I’m lost!
Mark Fanjoy
June 11, 2010 at 12:44 pm in reply to: Wrong Configuration To Imrove Rendering Speed?

Thanks Allen, for the response. I’m a little bit technical, but I think you are basically saying my rendering speed is what it is based on my current computer system and the Dulce Drives will not help much in that Department. Bummer.

I’m on FC6.06. Has that issue been addressed and will I improve rendering performance with a V7 Upgrade?

Thanks again.

Fanjoy

Wherever I am…I’m lost!
Mark Fanjoy
June 4, 2010 at 6:41 am in reply to: FCP Forcing Re Render When Outputting To Tape

Sam, your memory is still in tact. We tested the disabled sequence clips and PRESTO, the output to tape starts up with no forced re render.

You just saved us HOURS (and me lots of money!) of frustrating time watching my projects re render.

THANK YOU VERY MUCH for your support on this site. You guys are always so helpful and generous with your time!

Fanjoy

Wherever I am…I’m lost!
Mark Fanjoy
June 3, 2010 at 6:28 am in reply to: FCP Forcing Re Render When Outputting To Tape

Hi, Sam. I’m using 6.06. Yes, we do disable sequence clips often. I am almost sure however, the last few spots had no disabled clips. Worth another look, though. Will test and respond with an update.

Shane, thanks for your tip. Waiting for my editor to confirm his setup. Will update on that one as well.

Fanjoy

Wherever I am…I’m lost!
Mark Fanjoy
May 22, 2010 at 6:46 am in reply to: QT Movie File Output For DVD Studio Pro Authoring

Thank you very much Elliott, for your advise and direction. Much appreciated!

And thanks for looking out for us rookies. We’ll catch up!

Wherever I am…I’m lost!
Mark Fanjoy
April 10, 2010 at 12:48 am in reply to: Using Quicktime Conversion – WMV Output Errors

Lisa, someone else may know more, but my solution came in this thread. As soon as I installed the full version of Flip4Mac, WA-LAA. Done. I have WMV conversion at my fingertips.

It was an easy solution. The option pops right up there in FCP.

Wherever I am…I’m lost!
Mark Fanjoy
March 29, 2010 at 6:15 am in reply to: Title Safe 4×3 Lines For HD 16×9 Display

Yep. Locking the track did it. You ‘da man!

Thank you all very much for your input and support (and patience with the rookies!)

Great site!!!

Wherever I am…I’m lost!
Mark Fanjoy
March 29, 2010 at 12:16 am in reply to: Title Safe 4×3 Lines For HD 16×9 Display

Andy, I lied. One more question!

I have set up a two-camera multi-clip edit to switch back and forth. But when I lay the Guides over the multi-clip sequence, the two clips no longer show in the Viewer, only the Guides.

Can I not use the Guides in a multi-clip edit setting?

Thanks,

Wherever I am…I’m lost!
Mark Fanjoy
March 28, 2010 at 11:42 pm in reply to: Title Safe 4×3 Lines For HD 16×9 Display

Thanks, Andy. One last confirmation from you about the guide’s color bars.

Red is title safe, green is graphic safe, and blue is absolute 4×3 border, correct?

Thanks,

Wherever I am…I’m lost!

Page 7 of 12

← 1 … 6 7 8 … 12 →